Search results

3.50 gears. Open Differential. Complete backing plate to backing plate. Good shape. Clean it up, paint it, put brakes on it and wheel it.

I pulled a hydroboost brake booster and a Saginaw dual return power steering pump off a 78 Lincoln (continental or town car) with a 400 (i believe 400, maybe 460). I cut the hoses because the yard charges for them and they should be replaced anyway, but all the fittings are still there. I...

Brand new one inch body lift purchased a couple years ago from Wildhorses. Was planning to swap a NV3550 and never did. No need for it now. They are 100 bucks new on sale. All parts and pieces still there. Urethane mounts and all hardware.

I have a set of vintage aluminum slot rims. They are 15 x 7 size. 5 on 5 and 1/2 bolt pattern. 4 inch backspace. 4 and 1/4 center hole for the hub. I don't know who made them. They have some corrosion on them. Not on the face. Mostly inside the rim(inside the tire). It cleaned off with...

I have two vintage aluminum slot rims. They need to be cleaned and polished. They are 5 on 5 and 1/2 bolt pattern with the 4 and 1/4 center hole for the hub. 15x8.5 size Made by Superior Industries. SuperDrag I rims. 1580 lbs. 3 inch backspace. There is some minor scuffing on the face...

I wish all car/truck/vehicle forums were are great as this one. I have been here a good amount of time. I don't have an EB right now. I have a 78 Bronco and (don't flame) a Toy Land Cruiser right now. The sites I am on for info on these are so much worse than this place. The knowledge here...

This is pulled from a 79 Lincoln Continental with a 6.6L 400 V8. The vehicle was not running, so I don't know if they work. The PS fluid did look decent when I drained it out. The core value on the booster is $35 alone. You will need to have new pressure hoses made. The dual return Saginaw...

This is a custom made spare tire carrier that mounts a spare in the rear quarter window area of a stock hard top. The carrier bolts to the top on the quarter panel top bed rail and the lip above the window. The item is boxed and ready to ship. If you want to figure shipping the box is 22x22x8...

I know the bellhousing is different on the motor side because the 351M uses the Ford big block bolt pattern. My question is on the transmission side of the bell housing. Will the NP435 and/or T18 from a 78 Bronco bolt up to a V8 Windsor block bell housing? Without an adapter? Thanks.

Sold sold

Sold sold

Custom made spare carrier that mounts in either quarter window of a full top. I never used it, but I guess it would work for up to a 31 inch tire. I also don't know if will fit if you have a rollbar or cage. This thing is solid. It mounts through two of the bolts that hold the top to the...

A9P Computer. SOLD Mass Air Computer and Engine harness. All connectors still there. No cut wires. SOLD

My bronco is finally done after several years of off and on again restoration/driving. I have had it mostly done for a while, but now it is complete. It is Boxwood Green with Wimbledon White top. Ranger trim. 3.5 susp lift. 33x10.50.15 BFG MT's on Slot Mags.

I got an older model Warn 8274 all wired and bolted up today. I also finally got my driving lights back on my bumper after several years without. I am running dual batteries with a battery isolator. The winch is an early 80's vintage winch. Also check out some new letter inserts on my grill...

I found what I needed.

All prices negotiable. Shipping not included unless specified. 69-77 Used Headlight rings steel. No rust - $20 pair Tailgate support restored - SOLD Tailgate latches restores - SOLD Fuel Gauge switch and bezel used good condition - SOLD 67 style new repo window cranks - $15 pair shipped New...

89 Mustang computer & engine (injector) harness - $150.00 A9P mass air computer - $100.00 87-93 Mustang Stock Valve covers - $20.00 95 Explorer serpentine sold

SOLD Thanks

I plan on using a battery isolator to separate the batteries. Running the original wiring on the main battery and running a winch on the second battery. How do you get battery power to the 3G alternator charge post? Does the isolator prevent battery power from going both ways through its posts?