Search results

Im trying to connect the negative battery cable to engine block on the passenger side front part of block where it was connected before engine removal and machining. Does anyone know the bolt size of the threaded hole? See arrow in attached pic. Ive tried several different sized bolts and none...

I have BCB's shorty headers and 2 into 1 exhaust that goes into a Gibson Superflow round muffler. Everything fits perfectly. Is there a ready made/pre bent/off the shelf 3 inch exhaust pipe that can go from the muffler back to dump behind the rear passenger tire? Thanks

I'm installing the 3g alt with painless harness. On the alternator voltage regulator plug, the wires aren't color coded and in not sure which wires correspond to the yellow, green/red and orange to connect to the wiring harness. Is there a way to determine which voltage regular wire goes to the...

Folks, I've installed the Explorer serpentine swap and now wondering how you run fuel line from drivers side frame rail to the front of the carburetor. There doesn't seem to be an easy way to keep the fuel line in front of the engine block. The only option I'm seeing is running it on the...

Folks, A while back someone had a very good and simple diagram of which heater hose connects to each of the explorer serp water pump barbs. I’ve used the search function and can’t find it. Can someone direct me to the thread? Thanks in advance!

Was hoping to install the Exp Serp and ran into a bit of an issue. I think I’ll need a 1 inch BL to make it work. Thought I’d post here before doing so just in case I missed something

Looks like Suzuki is borrowing from the Bronco concept. https://truckyeah.jalopnik.com/the-2018-suzuki-jimny-should-be-a-perfect-tiny-4x4-1819085516

Folks, I'm doing the Explorer serpentine conversion on my motor. I've read the conversion tech article more than a few times just to make sure I'm doing it right. My question is thermostat direction now that coolant flow is reversed. In which direction should the thermostat now be...

I'm doing the serpentine conversion on my 76 302. Do I need to slide the oil slinger over the crank extension before installing the 5.0 timing chain cover? I'm reading the serpentine conversion tech article and didn't see mention of it. Note: I'm also rebuilding the motor (using Tom...

Folks, I recently removed my transfer case to reseal it. It had on a J style lower transfer case boot. I've searched and can't find a lower boot replacement. Does anyone know where I might be able to get one?

Folks, I'm installing a Painless Harness on my 76 Bronco and managed to reach a point where I'm not sure how to proceed. I've installed the glove box, fuse box, routed the 3 bundles through the firewall and am working on the dash. I didn't take the dash out because I thought I could install it...

*Not mine. Found this surfing craigslist* https://seattle.craigslist.org/see/cto/5683993690.html

*Not mine. Found this while surfing craigslist* 1967 Ford Bronco https://seattle.craigslist.org/see/cto/5715404801.html

*Not mine. Found it surfing Craigslist* 1970 Bronco pickup in Chehlais, WA https://seattle.craigslist.org/oly/cto/5704941275.html

I'm currently starting installation of the Painless Harness on my 76 Bronco. It has the passenger side firewall hole so according to the instructions, I have to route the bundle of wires labeled Passenger Side Firewall Opening towards and past the 2 fuse blocks. I removed the large zip ties to...

http://uncrate.com/stuff/woody-ford-bronco/ Maybe it should've been called the Country Squire Bronco.

I've read numerous posts about the Moog springs and am looking for a vendor that sells the CC810 springs. Summit doesn't have them and my local Oriellys says they're no longer available. Does anyone know of a vendor that still sells them?

Nice short video with Rod Hall and the Bronco he won the 1969 Baja in. http://jalopnik.com/off-road-racer-rod-hall-talks-about-the-cars-he-loves-1723359106

im doing the explorer serpentine setup on my 76 302. If I purchase the reverse rotation water pump like the one at BCBroncos I can use my stock radiator and stock configuration hoses without having to use crossover hoses, correct?

Folks, I'm hoping someone can point me to a good engine machine shop in the Poulsbo, Silverdale, or Bremerton, WA area. My bronco has a low mileage 302 and I'll be replacing the heads, cam, and intake for a little more pep (have smog era heads, timing chain, etc.) so I thought I'd disassemble...