Search results

Going to try this again. Anyone who has any Centennial or Bicentennial Mats (I see them listed as both) they are willing to part with I would be interested. Thanks! Jimmy

Good question. No. It wasn’t. It’s weird. It doesn’t seem to happen every time but when I was testing the blinkers and brake lights everything was working fine. I would then take my foot off the brake and but the turn signal back to the neutral position. (Hazards off). At this time the lights...

So. I took the switch back off. I don’t think the pins on the back were making good contact. I bent them a bit and it all seems to be working. Now for some reason though if I turn on my turn signal the lights start all blinking! I think it may be a bad flasher. This is easy And cheap to...

So, moving the turn signal does allow the brake lights to come on. But not both at the same time. Trying to figure out how to position the switch so that it all works. How did I install it wrong?

Ok. So if the turn signal and hazards are working but the brake light how would I fix that?

I did just change my turn signal! I didn’t realize these were linked to the brake lights. I can check there. Thanks.

So, when I put on the hazards the lights work fine. Does that help narrow down the source of the problem? Where should I look?

Was hoping I could get some help running down a wiring issue. My wife noticed my passenger brake light was out last week. Was hoping it was just the bulb. No such luck. I have weathertight connectors and they appear to be in good shape and making good connections. I was able to test the...

Ok. So, it sounds like the engine is a Frankenstein. Engine body from a 90 and heads from 74 or earlier. One other question on the plugs. What’s the difference on the 45 and 46? The look similar in specs on the autolite guide. Also, should I go strait copper, or platinum/copper or...

Thanks for all the leads. I try to take a look tomorrow to see if I see anymore stamping. I am interested to find out because as I look for parts I’m not sure what to ask for because I am not sure of the exact engine. As an example I’m swapping out my spark plugs now. The current plugs are...

Looking for some help decoding an engine stamp. When I bought my ‘76 the engine had been swapped out. I’m trying to figure out the exact engine that was put in. I have looked online and as far as I can tell it looks like it comes from an ‘87 truck. Is this right? I am having trouble deciphering...

Thanks for the replies! Look forward to seeing the pics nsiti. I have seen I can go bigger with the tires but very interested in the look of the 32's specifically. Anyone else with this setup?

Ok. I've searched the forum for awhile now. I've found lots of pictures of 33/12.5/15 tires (which I'm currently running), but haven't been able to find any pictures of 32/11.5/15. I am trying to decide on the two (Most likely BFG All-Terrains) and was wondering if anyone had any pictures...

Thanks! I'll take a look. Are those snap rings for sale anywhere?

I recently had my lowing steering shaft replaced as there was some slack in the U joint. After replacement the steering wheel moves in and out. Not the entire column only the inner shaft. Is there a retainer clip or clamp for this? I know there is a clamp for the column on 75s and lower but...

Thanks! I will check those spots. I just had a cowl seal placed. I am still seeing some leakage after that. i will check the air vent. You just seal around the edges of the vent? Thanks for the tips!

Mine is a ‘76. Sent from my iPhone using Tapatalk

Wanted to get some insight on this. I read a previous post about a leak from the dash. I checked the spots stated but dont see anything from there. Any thoughts on other common areas for leak? If it rains i just have a puddle in the center of the floormat. No real rundown from the...

Looks like the centech sockets are different in that they don’t have metal tangs. They are plastic pieces that snap in. So I don’t think bending them is an option. Sent from my iPhone using Tapatalk