Search results

I just searched all the threads on backspacing. With no avail. Can anybody tell me what the origional bronco wheel backspacing is, and what is the rim width. Or tell me how to measure the backspacing.

Has anybody had any luck with new 6 cyl radiators from our bronco venders? Seem like I have heard some stories of them possibly leaking out of the box... any help would be appreciated.

Can anyone tell me if the Dennis Carpenter factory die rockers are a combo of the inner and outer rockers, Or is the inner rocker completely seperate.

I am installing power steering in my 66. I have a 200 6. I bought a BC Bronco bracket that appears to line everything up fine. I was wondering if any of you have used a bc bracket, and what you did for the adjustment bracket. The BC bracket is just the mount and pivot bracket. Any and all...

I have a 200 six with 411 gears now. I am running 33 tires and this seems like the perfect setup for running around town or on the highway. My problem is when i throw my 16 foot jon boat or my 4 wheeler trailer behind it. No problem on the flat, but going up a hill without previous speed...

I am looking at buying a twin shifter for my 66 bronco..... but I know it is not a j-shift, and appears different from the standard t-shift handle, although it shifts straight up and down. What do I have? Thanks Hank

I have searched the threads and most of them talk about v-8s and c-4 trans. I have a six 200 with 3 speed man trans. It has 4.10/4/11 gears and am running 33 9.5 bfg at tires. I need to change my gears, but was unsure of to change them to the stock 456, or to split the diff and go to the 430...

I wrote the other day why after replacing my shift collar i only had reverse and first gear... I found out my shift column hole in the top was now a slot, and had been brazed before on a earlier repair. anyway i ordered a new tube from jbg and put it all back together and now i just have my...

Hi i am under the dash now and having problems putting my shift collar and turn sig collar back together I quickly looked for archives, but am running out of daylight . Does anyone know a site i can get a "clear breakdown on a manual column for a 66 Thanks Hank

I have a good bit of slopp in my 66 steering. I have replaced the suspension, brakes, and all of the steering components, except the gear box. If I grab the steering shaft just behind the box and twist it, there is quite a bit of movement before the pitman arm starts to move. It looks as if...

Has anyone else had a problem with the 6 cyl exploding mufflers? The first one was with the single bar carb.. and i had the timeing off and could not get it started. I kept pumping the gas and when it lit off boom. This time I have changed the single bar to a weber 2 bar carb. The motor is...

I have read some articles that tell you how to change the gear in the transfer case..... my calculations say i need a 14 tooth gear, and all i see in the articles i have read are 16-21 tooth gears.... any help would be appreciated. hank

My 66 bronco has a 6 cylinder motor in it. I was told that it has a dana 20 in it. The shift pattern is different then the j shift and similiar to the t-shift. But on my shift knob I have , from top to bottom.... 4-low, nuetral, 2-high, 4-high. But if i shift from nuetral to 4-low i have a...

I have a 200 inline six in my bronc.....when i went to replace my alternater from a local parts store ....... all i could get was a 60 amp or so alternater. Is there a 100 amp alt. with the same bolt patern and belt allighnment Thanks hank

Dana 30 3 speed manual dana 20 tranfer ford 9 rear what fluids are recomended for each of these.... I dont think mine have been changed for at least 15 years. Engine is out, so now is a good time. Thanks, Hank

Hi all, I am new to this forum. I have a 66 with a 200 6 in it. I have had a broke motor mount bolt for quite some time, and finally the other bolt broke. I was going to pull the motor to repair those items, and paint it up and a few other things. While I had it out I thought it would be...