Search results

Thanks, have some of those I just haven't put them in. It went back to popping out of gear. I may just put the factory tailshaft back on and see what happens. I also have a rebuilt D20 ready to install. Can't decide where to start.

I talked with AA. They said all of the troublesome assembled output shaft assemblies were off the shelves. The t case did not jump out of gear today. Maybe a simple fix, at least for now. Thanks for all of the advice I appreciate it.

I Thanks I'll call them tomorrow. It would be reasonable to think that they would have stopped selling the early ones as soon as they discovered the issue. It did not come with a gasket. I called WH to see if needed one. they said just use sealer. Would this make a difference? I also checked...

My Dana 20 J shift transfer case has always shifted perfectly. I recently installed an Advance Adapter heavy duty tailshaft. It was pre assembled. I installed a new Tom Woods driveshaft. The transfer case started jumping out of gear. I installed new detent balls and springs. It still jumps out...

It can take forever to settle. I removed the 3rd leaf from the wildhorses set. that was a few years ago and it's been the same height ever since.

Bright white Procar Elite bucket seats, used Purchased from Wild Horses. They are in good-excellent condition. They have new, never used, sliding brackets with springs and hoop style adjusters For 50.00 I have a new set of installation brackets from Tom's Bronco Parts. I am a sponsor but I had...

Is the AX 15 a used Jeep unit or a new one? It's my understanding that the new units are considerably stronger. I've been using one since 2011. High torque, high compression 347, 350 gears, 33s. I live at high altitude and offroad it frequently. No problems, great on the mountain highways, very...

Novak Conversions sells the correct bronze bushing, or at least they 2 years ago.

If you have an MSD analog box, I'd be looking at that first. They can cause all kinds of intermittent electrical issues, many of which are heat related. I have Fitechs on two vehicles. On one I removed all of the MSD stuff, it now runs perfectly. It used start breaking up at 3,200 RPM. The...

Reverse rotation was used to balance the smaller, lighter boats for driver position. Now inboard boats have become big heavy tug boats, so no need for any drivers side lift. The 427 is a much sought after marine engine, they're considered to be one of the best, and strongest ever made.

I'm not familiar with any ski boat transmissions that convert the directional torque to the opposite rotation. Do you know who makes them?

Thanks for the replies. I actually would have to buy the whole boat. The trailer is good, the hull is fair. The trans is good. Parting it out for the engine would probably be more trouble than it's worth. I was actually hoping it was a reverse rotation as I have boat that could use it, and even...

I've come across a 351 engine in a 96 Mastercraft. It's a PCM marinized engine. It's being called a GT40 EFI engine. Do any of you know if there's anything special about this engine?

Make sure the small slanted grooves on the section of the crank that the seal rides on are clean. The grooves push the oil back toward the inside of the engine. I once had a 302 that had a reverse rotation crank installed by accident, and the grooves, which are slanted in the opposite...

Thanks for the help. Looks like having a set of winter wheels is a thing of the past, just not worth the hassle twice a year.

Not directly a Bronco question, but I do us this vehicle to transport the Bronco. I need to know if off brand wheel sensors will work on late model f250. I have a set of wheels I would like to use for winter tires, but the sensors that came with them are not ford brand, although they are made...

wheels Do you still have these wheels?

I have one. It puts out good cold air. It is loud. It's definitely better than no ai,r but don't expect it to cool the whole truck. I'm not sure if vintage air will either. It is loud.

I have found that my 347, with a Fitech, runs much better with a Mallory magnetic pickup dist than it does with a timing controlled MSD dist. The Mallory has the factory advance curve.

I used 4" black pipe insulation. It fits nicely in the slot, removes easily for cleaning. It also costs about $10.00. It's very hard to even notice that it's there. Mine's been in for 9 years,