Search results

Day 1 reservation Order Confirmed on Mar 18th Production Date - June 25th - scheduled Aug 9th Production Date Updated - July 30th - scheduled Aug 16th Production Date Updated - Aug 7th - scheduled Sept 20th Production Date Updated - Oct 1st - scheduled Oct 25th Oct 29th - email has been built...

Can I purchase the pigtails that connect to the gauges somewhere or must I reuse the old ones from my old harness? Same for the gauge cluster lights. thanks, dan

Trying to sort out some ignition issues and i have no clue what distributor this is. Any one have any ideas? i think it might be an MSD since i have an older msd 6A and an MSD coil. this is probably 15+ years old. It has been locked out and the vacuum advance is not actually functioning...

Is it possible to do hard lines for my EFI along the frame following the original path? I would like to utilize a set of the stainless clips I have in the parts bin from BCBronco's and then just do AN fittings on the ends. I would then run 2 feet of the high pressure rubber lines on each end...

It is a 67 but has a later model filler neck. It currently has a port for vent, but it is blocked off. I will hit the junkyard and find a decent vapor canister to install. I will also try to find a a decent air cleaner setup. I will take some pictures of the instructions with the epoxy...

So I put a new aero tank on the rig with sniper fuel injection. I now have a persistent gas smell in the garage that requires me to leave the door cracked open. The sniper unit is actually working well and starts up immediately, leading me to believe that there is pressure in the supply line...

I am moving to an intank pump for my EFI system. Currently it is an external pump with the AN-6 fitting and the new gas tank is setup for a Ford Explorer intank pump. Are there any conversion fittings I can use to connect the AN-6 to the quick connect ports coming off the Ford Explorer fuel...

well - I ended up using a relay that is triggered by either the I pole on the starter relay or the green/red from the ignition switch. No reset during start. Now to let it learn.

Can I use the Coil + location with an MSD box? The Sniper install directions have the 'don't use a dirty power source of the coil' and I also am concerned about getting interference from the MSD box. thanks, dan

Newly installed Holly Sniper on a 289 utilizing MSD box for timing control. When I crank over the engine - the Sniper unit acts like it is rebooting and then starts. I am guessing that the pink sniper wire (on with both crank and run) is momentarily cutting the power. It will start up, but...

The most important part of the whole build is your kids working with you, cherish that time because it goes away. If you can get it running and drive-able - that provides the motivation you need on the next phases. Don't let perfect get in the way of progress.

I have a 79 Ford auto tilt column in my 67. Just sitting in the garage with everything off, I can turn the wheel 15-20degrees before I feel it 'tighten'. All of the linkage is new and I see the ujoint at the steering box moving the shaft coming out of the box. What can I do to tighten up that...

On CL - not mine. https://boise.craigslist.org/cto/d/1967-ford-bronco/6350444543.html

They don't have it listed on their website anymore. I sent them off an email, but no response yet.

Looking for a Gear Gawker for a D20. Can't find it anywhere online - any assistance would be appreciated. thanks, dan

I can have these delivered to the Portland Swap Meet - April 7th - 9th if desired.

I have a set of prerunner front runner fenders off my early Bronco - http://www.wcb4x4.com/mm5/merchant.mvc?Screen=PROD&Store_Code=WCB&Product_Code=10067&Category_Code=EXT Changing the look of my bronco from a SCORE racer back to a stock Bronco. They will need to be repainted to your color, but...

What is the part number for the 1/2 quart fuel filter that is utilized in the short version of the BCBroncos accumulator? I have the model with the tall NAPA filter and would like the shorter filter. Thanks, dan

He is - I just don't believe he really checks this forum often. I will PM you his phone number.

I think it is a bit more of a project than they are thinking. http://boise.craigslist.org/cto/5763452986.html