Search results

Orange fiberglass door inserts. I never installed them, but they came with my '75 bronco. No hardware. I will try to get pics soon.

For sale - Classic Bronco gas can carrier for the rear tailgate of a bronco. $75 Would rather not ship, but if you make the arrangements I will. Located in Tulsa, OK.

SOLD! Thanks for looking.

1975 Bronco with: New paint job Rusted floorboards were cut-out and replaced Entire interior and underneath has POR-15 applied on it 302 with fresh rebuilt heads (the higher compression ones) Motocraft 2-barrel NP435 granny 4-speed with new synchros New clutch J-shift Dana 20 BRAND NEW...

I have a complete NP435 assembly (J-shift Dana20) that I am wanting to swap for a C4 assembly, BUT............ I live in Oklahoma.%)

I am looking for a good C4 that I can put in a '75 Bronco with a 302 and J-shift Dana20. I have a NP435 now that I would be willing to do some trading. The wife does not want to shift anymore and it is technically her Bronco.%) Can call me at 918-625-6429. I am located in Tulsa, OK. Email at...

Oreily's, Advanced and Autozone sell remanufactured heads for about $150. Is this a bad idea? Also, how do I know if I have smog on mine or not? Why does that matter on the heads? Thanks again.

They do have a BA on them also, but not directly after the D2OE, (if it matters). So, is it safe to assume these are 302 heads from a '71-'74??? Also, is it safe to say that a smaller cc chamber head has more compression than a lrger one? Ex: A 58cc head would have more compression than a 63cc...

I have a '75 bronco with a 302 (I think). The guy I bought it from told me it had 351 heads on it, but who knows. I am not sure it even has a '75 motor.%) Anyway, the heads are shot and I was going to get an different set, but need to make sure of what I got and what I SHOULD get. The...

The fuel pump is new (I know, that doesn't mean anything for sure) and the dying problem is real intermittent. Like today, I drove for 30 minutes straight and it never did it, but I never got over 50 mph. As for the float level, maybe, but this carb (3rd one I have tried) came off of a good...

Any other ideas or suggestions?

Ok, I no longer have this expansion tank. What's next? Vented gas caps?

So, did you put on vented gas caps?

What panel?

Wow, great first post. I am not sure about the sucking in air thing, I will check that along with the lines. I am pretty sure they are rubber, at least where they go into the selector valve. So, are these tanks vented and mine is just clogged? Is a vented cap something alot of people do? If...

Yesterday, my bronco was parked outside and after the temperature outside started to warm up, fuel started to leak from the cap on my aux. tank. I assume it was pressure from the heat outside that caused this. Are these tanks vented? If so, where? I am also having a problem, every so often...

Any other opinions and/or suggestions?

I do not want to run my carb. and this is an auto truck. So........ I will need: 1. Car intake to clear the hood. 2. Flywheel and balancer from ?????? to adapt my tranny to the new motor. 3. Will my clutch work with the new flywheel? 4. Is the water pump outlet or the pulley configurations...

I have a '75 bronco with the stock (I assume) motor with a NP435 swapped in behind it. I have the chance to buy an '89 f150 (2wd) with a 302 (fuel injected?) with 94,000 miles for $200-$300. I would get the whole truck and it still runs, just been wrecked. 1. Is it worth that much? 2. Will it...