Search results

Hello, I am looking for a T-style drag link. Thanks!

I am looking for a T style drag link. Preferably in SoCal to save on shipping. I am in murrieta, temecula, and can make it to San Diego or riverside. Thanks

Looking for a set of complete 11 x 2 1/4" drum brakes (big bearing). Don't need the backing plates, but need, shoes, springs, brackets (all internals), drums and e-brake cables if you have them.

I am looking for a recommendation for a mechanic/shop to rebuild a '77 rearend that I have. It was sitting outside for quite a few years and needs a complete rebuild. I live in Murrieta, Ca. Also what should I expect to pay? Thanks.

I have some Early ford Bronco parts for sale: 1977 302 stock intake manifold $20.00 (spf to Ovalis) 1977 2bbl Carb $20.00 (spf to Ovalis) 1977 302 distributor with harness coil and brain $20.00 (spf to Ovalis) 1977 "Y" steering linkage $20.00 (spf to Ovalis) 19?? stock for power steering...

I have a 70 with a D30 front end and a 3inch suspension lift. I have the lowered track bar bracket on as well. I have a 77 D44 front end I want to swap in, but will the 77 track bar work with my existing track bar lowering bracket? Or is there another track bar bracket required? Thanks....

I have a "77 D44 that needs Pinoin and carrier bearings,seals replaced,and I have the rebiuld kit. Now the whole axle is out of the truck and has been dissassembled except for the gears. The local shops (Temecula) want to charge $300.00 to $500.00 for labor. Ouch! Anyone know of a SoCal shop...

There is a full hardtop sitting on the side of the freeway on the 215 South by the Ramona expressway South bound. The top itself is banged up bad but I did stop and notice that all the glass is good and the liftgate is intact. I allready have 2 spare sets of glass...

I recently bought an older model Warn winch (cable controlled), and bumper. Can you guys help tell me how to wire it up properly? Can I use a regular solenoid? If anyone has some sort of schematic or good description I would really apprieciate it. Thanks...

I am putting back together a dead 77' and am just now getting to the electrical. can you guys help me out by identifing a piece that was screwed to the inside passenger fender by one screw. It is a small box about 1"x1" and has three male tabs coming out of it. The wires that attach to the...

I have a 1977 D44 with disks that needs an overhaul. Gears are fine, but the seals are gone and since those are getting replaced might as well do the bearings. How much could I expect to pay a shop to do this? Thanks...

I have a 70 that did no come factory with an aux tank. so I know I have to get: The tank Straps and skid plate Filler hose toggle switch manual swich under drivers seat. Misc rubber hoses. My question: Is the wiring for the dash toggle switch in the harness behind the dash just unconnected...

Can someone post a pic of a 66-67 winshield frame hindge where it bolts to the tub. I have a weld in frame hindge and want to bolt it to a 66 tub. Thanks....

I have everything torn apart in my garage, and I lost the tension clip that goes behind the mounting clip on my D44 disc brake caliper. can I buy this clip seperate? does it come with a new caliper? Thanks

77 dash knob I've got a 77 that I am restoring and there is a pull type switch in the left hand bottom corner. The bezel and knob are missing. Any one know what this switch is for? It did not come with dual tanks...

Can some one give me a quick step by step to change out the D44 disk hubs. I have the calipers off but have never removed the hubs. Thanks...

What is the best way to remove the windsheild frame from the tub? assuming I want to preserve the winsheild frame. Thanks....

Help! I recently bought a 77. I am getting quite a few parts off it for my other Bronco, but I wanted to eventually get this one running to. The fenders, doors, and quater panels are fine in fact this is a uncut bronco. Well after removing the platic floormat, it seems floor is ENTIRELY...

I have a 1970 Dana 30 (drums)with a T style tie rod. I recently purchased a 1977 Dana 44 (disks) that had a Y style tie rod. Will the T tie rod bolt up to the D44 or will I have to cut and re-thread the tie rod? Thanks for the help

I just picked up a Brake booster with a old Duff's bracket and Master cylinder. I seem to remeber that guys used to beat in the drivers side wheel well to make it fit. Has anyone come up with a better alternative or idea? I would really hate to just beat the Crap out of it.