Search results

Look what Aldi store has if anyone is interested.

New Chantix commercial. About 25 seconds in. Are they saying Turkeys drive Broncos. https://www.bing.com/videos/search?q=chantix+commercial&qpvt=chantix+commercial&view=detail&mid=0AED4FB729EAF5F37C460AED4FB729EAF5F37C46&&FORM=VRDGAR

Just thought I would offer a little info to those having problems with your axle seals leaking because the surface on your axles are rough or grooved out from the years of use. I just went through this after rebuilding my entire Bronco. Drove it a bit and the right real axle seal was leaking. It...

Been working overtime to get truck ready for SC next month. Everything looked to be on track until the initial start up and break in yesterday. Looked everything over many times to make sure all was hooked up right and fired it up. Started pretty easy and brought the RPM's right up to 2000-2500...

Got the back side of the truck finished up. Still shooting for SC in April.

Was wondering if anyone has a lower windshield trim piece? I have the other pieces and just need the lower one in good shape. Thanks, Ken

Got the body set on the frame on Christmas Eve. Now time to start assembly.

Getting the AAW wire harness installed. Just about done with the dash and harness. Polished up my original bezels and knobs and they came out pretty nice. I don't have to buy new ones now. Used my mini polisher with some fine compound and was surprised at how little effort it took. Ken

Well yet another direct fit that doesn't fit! I know it isn't a huge setback but one of those things that should be an easy one to do right. Was installing side marker lights yesterday and when I went to put the plastic nut inserts in the rear quarters they are too big. How hard can it be to...

Borrowed my buddies tube bender and started the 2 into 1 exhaust system today. Started on the left side as that will be the most bends. I have Duff's long tube headers with an M5OD trans and there wasn't anything out there already designed for that set up. I am running 2 1/4 inch from the...

I'm looking for a drivers side fresh air vent box. PO cut the top off mine for a fiberglass hood. Thanks, Ken

Got back to working on the Bronco again after painting it for the last couple of months. I think I have had enough of sanding for a while. Built a trailer hitch into the spare tire rack brace that is covered by the bumper. Also got my stainless steel hard lines ran for the fuel system. I picked...

Finally got the fenders, doors and grill painted. The body and tailgate are done. Just have the hood and roof to do before the cold weather comes. It's been a hot muggy and wet summer this year and not too good for painting without a booth.Ken

Been a long time coming. Was finally able to paint it today. This summer has been hot and muggy and not conducive for painting. I have been waiting for a window to paint and never really got one. I decided to use a very slow activator/reducer and let each stage flash off for a day before...

I am in the process of installing a 5 speed M5OD in my Bronco and got the trans out of a 90 F250 and it had the shift tower towards the front of the top cover. That would put the shifter at the front of the trans tunnel right at the cowl. I found a shift cover off a 1999-2004 F150 2 wheel drive...

I have gotten about everything mocked up and starting to disassemble for paint. It has been a long road to this point but has been all in all a good time. I wanted to say thanks to a lot of people on here for information and motivation. Ken

I was mocking up my steering column and did not like the look of the end of it inside engine compartment. I put in a M5OD and didn't need the shifter mechanism at the end of the column. I removed the bearing retainer at the end of the column by drilling out the spot welds. Then I cut the column...

I have some parts that I can bring to Super Celebration in April. Ken Added a couple more things. 2.Manual steering box, new seals,paint 100.00 4.Manual 3 speed trans-RAT w/bellhousing 100.00 5.Stock steel hood, no rust/few dents 150.00 6.Stock intake w/carb and heads 100.00 7.Dana 44 stock...

Got my fuel tank mounting brackets welded in and noticed they didn't put a vent in the tank. No bung or anything. Called Jake and he sent one. I was wondering if it needs to be on there when it will have a vented fuel cap. Would the fuel fill vent be adequate with a vented cap. It will be an EFI...

I just got the M5OD trans installed and mounted up the D20 transfer case. I used the BC crossmember and now the front output yoke is lower than the crossmember. Before I build a new crossmember I was wondering if the T-case can be clocked up a bit. I was told that this swap kit would work on...