Search results

Hi everyone I need some advice Today I hooked up my Painless harness to my steering column. I heard a click soundand then I checked the turn switch functions and everything workedgood. I forgot to check the horn but about 5 minutes later the horn went off and did not stop. I disconnectted the...

I am going to install my 23 gallon tank I bought from Tom's Bronco this weekend. Everything looks pretty straight forward in the instruction. My question is what do I do with the two EVAP outlets? My bronco had no fuel tank or gas lines when I bought it. (was on propane) Do I just block them...

HI Guys I am putting back to gather and noticed on my new doors I forgot to drill out new holes for the door locks. MY problem is since the bronco was off to paint the old original doors went to the scrap yard before I could make a template for where the hole should be. (they did not have holes...

I am bringing my bronco home form the paint shop this weekend. Have a question before I dive in and cause myself more work. I need to reinstall everything in the doors. I what order to you guys suggest I put everything back in: windows and runners door handles & locks vent window...

Was think the other night about the number of early Broncos hear in Europe. I was at a 4x4 gathering and realised it was jeeps or land rovers. with the odd land rover. Our vehicle register in my country says there ore only a handful with plates. So I am going to try to put together a list and...

Purchased a fan shroud from one of the Bronco parts dealers made from pvc. I assumed it would be a one pieced moulded product but to my surprise it was multiple pieces screwed together and no mounting clips. Not a bad pice but not what I wanted in my bronco. So using it as a rough template we...

I am installing the 23 gal. tank in my 1967. I have followed the instructions and am curious what does the top of the tank push up against when I tighten the J hooks. As there are no brackets above as I removed the original ones as instructed. Does the tank just float off the J hooks. And the...

Looking for an original oil bath air cleaner(complete) for a 170 cubic inch 6 cylinder Dave d.r.young@mac.com

I have been reading threads and checking pictures and there seems to be no definite colour for the dash panel. My plan is to go with body colours close to original Which is "Harbor Blue". the interior listed on the Marti report says "Parchment" But the dash pad is black. Is that correct...

Probably a goof question... But what does everyone use for a fuel line from the tank to the pump? Looked through vendors catalogs only most do not even list anything??

I my other thread about installing the rear axles. I mentioned when I was done that I was going cut the ends of the U bolts since they were quite long. There is 3 1/2 - 4 inches of thread showing above the nut. It was mentioned I should not. But I think I go the extended u bolts by mistake with...

I was just at the vehicle registration in the Netherlands and there are only 3 early bronco registered here. (mine will make it 4 when the restoration is done and I have it approved) Just curious where else there are any over here..

HI A quick question before I proceed with re installing my rear axle and leaf springs.. Is it easier to first install the leaf spring then attach the axles to them. or assemble the axle and leaf springs then in re install onto farm?

Just wanted to let everyone know that Painless is doing a online survey with Texas A&M. Takes only 5 minutes and when you are done you get a 25% off coupon. Also a chance to win any product in the catalog for free.

I am rebuilding my knuckle on my Dana 30. I purchased the seal,bering & race. along with a damper kit (as I seen in schematics online) When I took the seal off and the bearing out there is no damper kit located below the race. Area was just filled with grease. My question is do I need to...

Hey everyone. I am not a tire guy but am sure you guys can answer my question. I brought my newly sandblasted and powder coated rims to the tire shop and ordered tires. Went back to get them and he said he was waiting for the inner tubes to arrive. I know the original tire had them (believe it...

First I would like to thank everyone for there advice & help when asked on the forum. I am a true Ford guy and have been restoring Mid Fifties F100's. But have always had a eye out for early Bronco. (had full sized bronco in high school) for reasonable money and condition. Then this past May I...

HI everyone. I am having a idea about what to do with my axle housings. I have them being sand blasted and have been throwing the idea around in my head of what color to powder coat them. The fram is mat black, the under side of the body is harbour freight blue so I was thinking what would be a...

I am in the process of planning out the rest of the build on my 1967 restoration. I have the body off and to the sandblasting and will ship to the metal shop. Now onto the frame and driveline. With regards to the 3 speed I would like the pro's & cons from everyones experience on installing a...

I know this question has been ask a hundred times. But I have not seen a definate answe. I have to special order the tires over here and they do not take them back. So I am doing a frame off restoration on my 1967 Bronco wagon. I will be keeping everything stock. So my question is what is the...