Search results

I have a metal half top (it was original please don't hate on me for modifying it :-) I started a project and haven't had the time or garage space to finish it. This metal stop was stripped and primed and the rear window was removed and the roof line was modified to fit over a wild horses...

For sale/Best offer. This is a metal custom bronco half top from a 69 bronco. The rear window has been removed and the top was reinforced slightly with some welded sections. Roll bar noches have been custom welded to fit a Wild Horses family style cage. We were going to prime and paint this...

Best Offer - I need to make some space and I have this full top from my 1974 Bronco. It hasn't been on the vehicle for over 8 years. Located in Hillsborough, CA not far from SFO It is in what I would say is just "ok" condition - I see some rust and cracked paint around the gutters. Best...

I bought a new Miloden oil pan for a 302 bronco Fits my 1974 Bronco It comes with a new dipstick and the pickup I didn’t like the pan, it leaked for me, but that is due to a cheap seal I used. So this pan was on the bronco for a month and then I removed it and went to stock. It’s a shame to...

here’s my question: 1) is it obvious to anyone here what brand of distributor this is? 2) is it something stock or aftermarket? 3) when some previous owner added the MSD would they have also typically changed the distributor or done something to the stock distributor internals? I’ve just...

Actually a serious post. My bronco makes a pretty noticeable whirring/wizzing sound right after startup and it seems to be mostly when in first gear. It’s a new sound and it coincided with a swap to my flex plate. it’s sort of a high pitched whir/wiz like a big gear spinning or a belt making a...

has anyone seen one of these round air cleaners recently new or used? I may try the WTB side of the forum. I’d like to find one https://www.summitracing.com/parts/fms-m-9600-l302

I was going to try and remove any unnecessary wires and parts after a 1-wire regulator installation. I’m sure that’s been talked about before and i’m searching the forum for any links that might walk through it. The key question is, what’s unnecessary? what can be removed? When I look at my old...

I was going to try and remove any unnecessary wires and parts after a 1-wire regulator installation. I’m sure that’s been talked about before and i’m searching the forum for any links that might walk through it. The key question is, what’s unnecessary? what can be removed? When I look at my old...

people, this is an embarrassing post but i’m going to post it anyway. somehow, I failed at a one-wire alternator installation. i’m on my third alternator now looking for some advice or diagnostic to run or... someone to come over and buy me a drink or something. here’s what happened: I did...

Thanks all for the help on my previous projects. I’ve been dreading this one and I finally started it this weekend. I’m going in to replace the timing chain seal because it leaks a little bit of oil and a little bit of radiator fluid. While in there it was recommended to me by others that I...

little bored here on the 4th of July with a global pandemic. spent some time today installing a new overflow and recovery tank. We went with this canton unit. was expensive I think, and it was OK when it arrived my first impression was that it is way over done in, welded everyplace - a lot of...

All, We had overheating issues with an AOD transmission on my 74 Bronco. We looked at all kinds of potential causes. We checked to make sure cooling lines did not run near any hot surfaces. Checked the TV cable and the pressure. We’re using the correct throttle cable “geometry” for our...

Guys, I am hunting for leaks in my 74 bronco and while looking I noticed something strange (to me) I would search for an answer to this question if I knew what topic I was searching for... On the left side (passenger side) of this Ford 302 engine I see a spot that looks like something belongs...

Thinking about selling this one. https://74bronco.shutterfly.com/pictures/131 I would take $29.5K. the pictures are posted on my "74 Bronco Website" but this blue Bronco is titled in California and is a 67. Carbureted 302 Engine Softop available. Automatic, 3 speed, shifter is on the floor...

Folks, I modified this post - i’ve sold the hub caps but I want to sell these wheels and tires. The rubber is basically new! somebody make me any kind of offer so I can get these out of my garage! You pick a price For sale I have a new set of 5 - BF Goodrich KO2 tires size: 30x9.5 R15s - and...

For sale I have a new set of 5 BF Goodrich KO2 tires size: 30x9.5 R15s The pictures below show 4 but i have 5 wheels and 5 Tires and a full set of Bronco hub caps that fit those wheels. The rubber is brand new. The rims I’ve had for a while. The hub caps are in good shape. I changed tire and...

I’ve though about doing some engine upgrades. Has anyone seen a clean solution for pumps and return lines for EFI when there are twin tanks? I probably wouldn’t even mind upgrading the tanks themselves but I don’t know what to do with the return lines and the cut over lever beneath the seat...

Guys, Any pointers or help would be much appreciated. I'm trying to return my 74 bronco front hubs to stock after someone did a GM disk upgrade. (I can explain why later if it becomes important) I have ordered and re-ordered used hubs.. and I now have 4 used front hubs and I'm trying to get...

Anyone interested in this? I have an unused Dakota digital Gauge for your 66-77 bronco w/ all the parts + a couple of bezels also unused stainless and matt/aluminum. I think it was $750 gauge and it sat in my garage for a year and I ended up putting a more retro gauge in...