Search results

I have Explorer EFI and Garry plumbed in the Mustang purge valve for me. I have a DeLorean rollover/check valve. The question is, when I run my vent line to the check valve do I need to run it high into the rear fender (making a loop of sorts) first to keep fuel out of it completely or can I go...

I'm selling my working C4 transmission, Dana 20 adapter, torque converter, cooler lines, block plate, cable kickdown, and B and M quicksilver shifter. Transmission has deep sump pan on it. I pulled it in December to swap in 4R70W. Transmission was rebuilt approximately 20k miles ago. Worked...

I'm right in the middle of rebuilding my transfercase and in the process of installing the extreme output shaft kit into my old output housing. The issue I'm having is with the small bearing race. It is not a press fit. It's a little snug but it drops right in. The stock replacement in my...

I am selling both the stock rear main tank and auxiliary tank. Both tanks include straps and skid plates, as well as any hardware I have. I am asking $50 each. The main tank was used up until a month ago. It has no rust and the sender worked fine. This tank is a pre-emission tank and only has...

I've read Explorer build posts for the past couple of months and have a pretty good handle on what to expect while doing an Explorer Swap. I recently ran into a deal for 1998 Mountaineer from friend. Got a great deal but it's a high mileage truck (255k), runs good though.I drove it around for a...

Dana 30 without spindles, 3.50 gear set. Pick up only. $150.00

I have one of the dreaded leaks at the dipstick plates on my oil pan. I am planning on pulling the pan tomorrow and welding the plates. I want this to go smoothly and get it done in one day so I want to make sure I'm prepared. I had the oil pan off a while back when I rebuilt the motor but I...

So I'm starting back up my quest to convert over to Duraspark from points. I was reading in past posts that you can actually take the guts out of a Duraspark dist and put them in the old points dist. If that is the case, can the old cap and rotor off of a point dist run on a Duraspark. I have...

I am looking for the measurements of a c4 dipstick. I have several donor sticks that I can cut down and mark for fluid levels. Any help would be great.

I am wanting to re-seal up my diff as oil seems to seeping from the pinion, housing to diff, and pinion housing. My question is can The pinion housing be separated and resealed without messing up ring and pinion adjustment? Can the pinion seal be replaced without messing with the crush sleave...

I knowthat these boxes are found on Toyotas and Nissans, but what year and models of these makes are they found on? I might have a lead on a wrecked 95 4runner and I am curious if this is the same delphi box used for the Broncos.

Years ago my speedo stopped working and I pulled the cable and saw that the teeth on the cable gear were chewed up. Years later I got around to replacing the chewed up gear. After replacing the speedo still did not work and come to find out that it was the speedometer itself that was locked...

Today I pulled my front end apart to replace the inner seals. While removing the carrier I noticed something up with one of the bearings. One of them was loose, loose enough to be pulled off. The bearing did not look like it had spun, but it did not look right to me. The question is, can you...

How much vaccum should a 302 make?

Anyone using one of these carbs, are you running a 1 inch spacer? I am on my Holley since the stock 2 bl had one and I needed a PCV port. So do you need one for any clearances with the Edelbrock/Carter?

I was exploring the idea of swaping to a quadrajet. I know BC sells Jet versions, but that comes with a hefty price. I was also looking at the Summit Universal Quadrajet calibrated for small blocks. Has anyone ran these? Am I on a wrong track? I would get an old used one and rebuild it, but...

My stock radiator is shot and will need replacing. I have made the decison to go copper only for the longevity and repairability. So the question is high-efficiency 4 core or stock 3 core. Does anybody have some good tips on which is better. Reading through threads many people comment on...