Search results

I have own my broncos for a few years, I have always loved eb's and today I was at My buddy Todd's house (MtnRam here this forum) and I realized I had never ridden a bronco not an early one..So Todd says jump in so he and his Little boy took me for my first ride ever in an early bronco....I was...

How many gallons are the factory poly fuel tanks, I just pulled one out of my other eb , I was think about using it in my current project but only if its bigger. Its doesnt look much bigger , the eb it came from had on one single tank. thanks, HOJO

I have the Extended ss brakes lines from Jeffs bronco graveyard. i was wondering I have the stock fitting on the rear axle and the block has a soft line coming in .. How do I make the new ss flex line attach to the factory block on the axle ..The block is one piece and it doesnt untread so I can...

Serpintine water pump pulley for a 94-95 cobra 302

What fuel pump set up is everyone using.. I have read about 2 pumps , accumulators etc.. just trying to get the best bang for the buck......

I have a build thread already but I wanted to start a new one , on just the motor install. I know I will have a bunch of questions and I have had many answered already...so here goes..... Stock 302 and engine compartment...

Has anyone had the problem , that when they put shorty headers on a 302 the collector is really in the wy of the clutch linkage..well it appears to be in the way ..I havent tried the linkage yet but it looks like ill have to mad something..thanks Lee

Is there a way to use my pump that I have from a 88 f150 to run my hydroboost ?

I have a 88 f150 air compressor of a 351 .. I was wondering if this was a good candidate for conversion to on board air.. thanks, Lee

I am putting a 94 cobra motor into my 73 . am assuming the 73 clutch will work .not changing the tranny or anything just motor? Lee

I have seen an Egr eliminator does that mean I can get rid of the qawky egr crap on the side of my intake

Has anyone tried these gadgets the eliminate the oxygen sensor, do they work well or a waste of money

I was wondering about using a "PUSHER" fan in front of the radiator, due to space. I know this is 15% less effective, but it would save so much space. I would love to know your thoughts and ideas or experiences Lee

I am collecting parts for my EFI swap and was wondering if I missed anything( for 94 svt cobra motor swap) I have the motor / intake /wiring harness computer distributor ignition coil oxygen sensors x2 bungs to weld into exhaust x2 MAF TPS ECT VSS ? TFI Idle Air Bypass crank positioning sensor...

Old for injections says "most commonly used distributor had the TFI module mounted directly on the side. The other distributor mounted the TFI module remotely in an aluminum heat sink on the fender or firewall, which can be identified by its wire harness pigtail" I have a 94 svt cobra motor ...

I am researching the daunting task of putting a cobra motor in my bronco, I have a 94 cobra motor almost complete, and a new computer. I have nothing else ie. wiring harness ...and I dont know much about EFI . I know there a losts of threads and i have been reading. I just though you gurus...

Im looking for a 5.0 upper intake/plenum off of a mustang or ford car , I have searched my local junk yards and not to be found. I hope to find one that wont break the bank...

Hello, I am working on a 73 , I upgraded the axles to full width and added a 5.5" suspension lift. I removed all the brake lines and cables , and I want to start in the engine compartment and work my way down and back. I was thinking about a complete kit from one of our vendors . I looked at the...

I have probably a dumb question but I dont know if a dana 20 will bolt up to an automatic tranny from a 92 f150 directly or will it require an adapter.

One of my emblems was in the glove box and its got most of the post still intacted I was wondering the best method for reinstalling it on the fender.. Lee